completed

Praxis II — NovaGlove Thermal Glove

How can astronomers maintain hand warmth at -18°C while preserving the dexterity required for precise telescope operation?

StatuscompletedDatesMarch 2026RoleTeam member · four-person design teamAffiliationPraxis II · University of Toronto
1

Context & question

How can astronomers maintain hand warmth at -18°C while preserving the dexterity required for precise telescope operation?

Designed NovaGlove, a heated double-layer glove system for astronomers working in cold outdoor environments. A silk inner glove, flexible polyimide heaters, manual PWM control, and a removable neoprene outer layer were combined to preserve warmth while retaining access to the fingertip dexterity needed for telescope operation.

Astronomy sessions can last approximately four to six hours in conditions approaching -20°C. Conventional winter gloves improve warmth but make fine telescope adjustments difficult, while removing them exposes the hands to cold and increases the chance of dropping small components.

The target stakeholder group included members of the Royal Astronomical Society of Canada and other amateur or serious hobbyist astronomers. A RASC representative responded positively to the concept, but the organization is not presented as a formal paying client.

NovaGlove used a thin silk inner glove with flexible polyimide heating strips, a 7.4 V battery, and a manually adjusted low-voltage PWM controller. A removable neoprene outer glove retained heat, accessible fingertips supported precision tasks, and neodymium fingertip magnets assisted with retrieving small ferromagnetic parts.

The formal requirements included operation at -18°C, a task-completion time ratio no greater than 1.5, accessible fingertips, waterproof electronics, freezer survivability, low weight, adjustable heating, and approximately ten hours of intended battery duration. Waterproofing and exact freezer-verification details were not fully resolved in the supplied record.

Validation included cold-condition task testing and a thermal simulation conducted in Python. At -18°C, NovaGlove recorded a mean task-time ratio of 1.20 and a mean error ratio of 1.14, compared with 1.60 and 1.77 for a regular glove and 2.09 and 2.18 for a bare hand. A separate simulation at -10°C indicated heat dispersion through all fingers.

Design requirement
-18°C
minimum operating condition
Task-time ratio
1.20
target ≤ 1.5
Mean error ratio
1.14
NovaGlove at -18°C
Thermal simulation
-10°C
ambient condition
Reported maximum
≈41°C
heating temperature
Battery duration
≈10 h
design claim
Battery voltage
7.4 V
Team size
4
2

My contribution

  • Worked directly with the client to gather requirements and suggestions on the team’s ideas.
  • Conducted secondary research into existing solutions and approaches suited to the client’s needs.
  • Handled the practical design and assembly of the glove, from collecting parts to integrating each component.
  • Stitched the heating strips onto the glove and connected the PWM controller.
  • Handled the practical demonstration of the completed glove.
3

Outcome

NovaGlove met the documented task-completion requirement in the reported -18°C comparison, recording a mean time ratio of 1.20 against a target of 1.5 or lower, with a mean error ratio of 1.14. The prototype integrated heating, insulation, dexterity, and small-part retrieval into one wearable system. Further work was identified in electrical waterproofing, battery and cable placement, fingertip access, zoned heating control, and long-duration environmental validation.

4

Excerpts

Prototype configurations, labelled components, the Python heat simulation, and the Praxis II presentation poster. Select any image to enlarge it.

Inner glove configuration

The silk inner glove carries flexible polyimide heating strips along the fingers, with wiring routed to the wrist.

NovaGlove silk inner glove worn on a hand, with polyimide heating strips along all five fingers and wiring running to the wrist.
Inner + outer glove configuration

The removable neoprene outer glove adds insulation over the heated inner layer, with flip-tip openings for precision tasks.

NovaGlove with its neoprene outer glove over the heated inner glove, showing flip-tip openings, wrist wiring, and an external battery.
Labelled components figure

The integrated heating and insulation system, with its battery, manual PWM control, heating strips, and fingertip magnets labelled.

Annotated NovaGlove figure identifying the neodymium magnet, 7.4 V battery, polyimide heating strips, PWM driver, silk inner glove, and neoprene outer glove.
Heat simulation (Python)

Thermal simulation conducted in Python at an ambient temperature of -10°C, showing heat distribution through the fingers and a reported maximum of approximately 41°C.

Simulated hand temperature distribution with warmer regions along the finger heating strips and a temperature scale reaching approximately 41°C.